— Dishwashers
Dishwasher Repair in Sherman Oaks
Draining, heating, and control issues diagnosed in one visit. Miele, Bosch, Thermador, KitchenAid, and integrated panel-ready machines are our daily bread.
- Typical range: $160 – $480 (most repairs)
- Usual visit: 45–75 minutes on-site
- Same-day slots: Yes, usually
Symptoms we fix every week
- Water pools in the bottom after the cycle
- Dishes come out wet (drying stopped working)
- Cycle never finishes or runs for hours
- Door won't latch or leaks at the bottom
- Grinding or humming when pumping
- Soap pod stuck in the dispenser
- Control panel unresponsive or flashing
- Error codes: E24, F0, LC, E15 (Bosch / Thermador)
- Dishwasher smells like stagnant water
- Spray arm won't spin
Ventura Boulevard’s dishwashers are quieter than they used to be
The two brands we see most in Sherman Oaks kitchens are Miele and Bosch, and both of them prioritize quiet operation over almost everything else. Miele runs at 38–44 dB, Bosch Benchmark at 39 dB. That quiet comes from heavy sound insulation, a condensation-drying system (no vent fan), and precision circulation pumps. When they go wrong, the symptoms are subtle — a slightly louder cycle, dishes that feel damp instead of wet, a faint smell that won’t quite go away.
We tune diagnostics to each brand. On Miele, we always check the turbidity sensor and the heat-pump impeller early. On Bosch, E15 errors get a full base-pan inspection before we touch the pump. On KitchenAid and Jenn-Air, the chopper blade and sump strainer come out first.
Valley water is hard on heating elements
Sherman Oaks tap water is hard — hard enough that anything heating it grows scale. Inside a dishwasher that means a crusted heating element, spray-arm nozzles that slowly narrow until the top rack stops coming clean, and inlet valves that stick. We replace heating elements ($180–$280) noticeably earlier here than the same machines would need on softer water, and a good share of the “top rack isn’t getting clean” calls we run end with a descaled spray arm rather than a new part.
Two cheap habits push that timeline back. Keep the rinse-aid reservoir full, and run a citric-acid descale every couple of months — Miele and Bosch each sell their own, and either works fine in the other’s machine. If your house has a softener, mention it when you book: softened water needs roughly half the detergent, and over-sudsing on soft water trips the Bosch E15 float more often than an actual leak does.
Repair vs. replace
A dishwasher is the appliance where repair-vs-replace is almost always the clearest math. A $280 heating element on a 7-year-old Miele is a no-brainer against a $3,200 replacement. Even on a $900 mid-range Bosch, a $300 repair is a better deal than buying new unless the machine has a history of failures.
We’ll tell you if a repair isn’t worth it. On the rare occasion we see a dishwasher with a cracked inner tub or a corroded sump housing, we’ll advise against the repair and help you understand what to look for in a replacement.
Book below, or call (818) 921-4254.
How we tackle a dishwasher call
-
01
Clear the drain path
80% of 'won't drain' calls are a clogged sump filter, a kinked drain hose, or a failed drain pump — in that order. We check all three before pulling anything apart.
-
02
Confirm electrical / control issue
If the panel is dead or flashing, we meter the control board, door switch, and thermal fuse before ordering anything.
-
03
Inspect the leak point
For leaks: door gasket, spray arm seal, water inlet valve, sump gasket — we run a test cycle with the kick-plate off to pinpoint exactly where water is escaping.
-
04
Quote and install
Most common parts (drain pumps, door gaskets, heating elements, thermal fuses) ride on the van. Clear quote before any swap.
-
05
Full cycle test
We run a complete cycle with the repair in place — fill, wash, drain, heat, dry — before packing up.
Brands we service
- Miele
- Bosch
- Thermador
- KitchenAid
- Wolf (Sub-Zero Group)
- Viking
- Jenn-Air
- GE Monogram
- Fisher & Paykel (DishDrawer)
- Asko
- Whirlpool
- Samsung
- LG
What a typical repair costs
| Repair | Typical labor + parts |
|---|---|
| Drain pump replacement | $180 – $320 |
| Heating element | $180 – $280 |
| Door gasket (tub seal) | $160 – $260 |
| Water inlet valve | $160 – $240 |
| Circulation pump (motor) | $320 – $480 |
| Control board | $300 – $520 |
| Door latch assembly | $160 – $260 |
| Turbidity / optical sensor (Miele, Bosch) | $240 – $360 |
Prices reflect common jobs on mid- to high-end appliances in Sherman Oaks and nearby neighborhoods as of 2026. Actual quotes are given in-home after a flat $49 diagnostic (waived with repair).